EXOLINE AQUA STOP B+ SMALL

Vapour and waterproof plaster additive

Exoline® Aqua Stop B+ Small

Article number:

EXO-ASB-010-450ML

Product type:

Additive

Product description:

Vapor and waterproof plaster additive

Read More

For the preparation of hydraulic bonded, universal, hydrophobic additives produced by nanotechnology, domestic and outdoor vapor and waterproof plaster.

Packaging:

450 ml plastic cylinder

Evaluation:

Year:

£ 8

Exoline® Aqua Stop B+ Small Need and Price Calculation:
Complete the contents of the yellow fields!
Height (m):
Width (m):
Plaster thickness (cm):
Sand £/kg:
Cement £/kg
Square meter:

m2

Cubic meter:

m2

Mass (sand):

kg

Gross price (sand):

£

Mass (cement):

kg

Gross price (cement):

£

Quantity (exoline®):

box

Mass (Exoline®):

ml

Gross price (exoline®):

£

Total gross price:

£

Exoline® Aqua Stop B+ video presentation:

Mixing:

Mix 1pcs of Exoline® Aqua Stop B+ Small "dry" with the contents of any 25 kg base plaster in circulation, and then prepare the desired composite in normal procedure.

Recipe recommended by Exoline®:

A bag of 25kg Portland cement (32 / II or 42 / II) composite

130kg sand (0-0.5 mm)

4pcs Plastic Box 450ml Exoline® Aqua Stop B+ Small additive

2kg flexible tile adhesive

Material Requirement: 15-16 kg dry mortar / m2 / cm

Water demand: approx.34-38 liters

Can be used:

Manual lapelings, machine -applied basics, plaster coatings, plaster plaster, masonry mortars, pre -sprayers, etc.

Construction adhesives, tile adhesives, Gres adhesives, flex adhesives, EPS polystyrene adhesives, thermo adhesives, etc.

Gypsum plasters, fillers and other cement -based powders.

Area of ​​use:

Old and new buildings, buildings, dwellings, industrial facilities, cellar walls, balconies, underground garages, tunnels, sewage storage, sewage storage, sewage reservoirs, reservoirs, fire storage facilities, recessed water tanks, bathrooms, bathrooms,pickling tubs, etc. for insulation of water.

It can be used effectively in the case of soil pap, deficiency, defect against soil moisture, and repaired water engineering problem.

Suitable for both positive or negative water pressure insulation.

It can be used below and above the plane of insulation, both outside and inner side.

The additive applied reduces the surface water uptake (hydrophobic property).

For new buildings, it is suitable for drying and drying the wetting plinth under the plane of wall insulation.

Suitable for the insulation of building structures, parts of the building for leaks, groundwater, use water, base plates, pillars, retaining walls, concrete, brick, natural stone, loam and mixed masonry plastering at least 2.5 cm thick.

It can be used for firing water storage, recessed water tanks, bathrooms, showers for water insulation.

Dry walls save heating costs in winter (evaporation heat).

Benefits offered by Exoline® product line:

Our products are primarily compatible with all commercially available cement -based construction products.

Using the product, you can change other systems, such as spreadable insulation, foils, heavy plates and other technological solutions.These technologies are obsolete expensive and significant requirements, and their preparation depends largely on human factors, which increases the risk, costs and time of construction.

Mixing instructions: I.

First, mix the contents of the 25kg cement and the 450ml Exoline® Aqua Stop B+ Small plastic box in a mixed box "dry" into homogeneous states.(In winter, the recommended cement quality is 42.5/II composite, while in the summer 32.5/II composite to provide good quality!)

Second: 1 volume (shovel) cemented with exoline® additives and (as needed) 3 - 4 volume (shovel) "general" (firing colonies, clay and mud -free) sand in normal procedure, repeated "dry" depending on the quality of the concrete mixerapprox.Stir for 3-6 minutes to homogeneous.To achieve excellent quality, use 0.5 mm of dried grade grade sand.

Third, after dry mixing, the plaster is mixed with the amount of water used in normal procedure (approx. 5-6 liters) for a minimum of 3-6 minutes.

Mixing instructions: II.

Previous: The Exoline® Aqua Stop B+ Small additive is added to any 25kg handheld in circulation.(The contents of the 450ml plastic box can be added to 1pcs of 25kg bags.)

Second, mix the ingredients for 3-6 minutes to "dry" homogeneous.

Third, after dry mixing, the plaster is mixed with the amount of water used in normal procedure (approx. 5-6 liters) for a minimum of 3-6 minutes.

Adding lime is not recommended for the additive and ready -made!

Mixing:

It is recommended with a low speed concrete mixer - a mixing drum at an angle of 35 ".

Preparation of wall surface:

The bad stone and brick pieces must be carved all the way to the hard part.

In the plinth area, clean the thickness of the wall above wetting.Eg: (Sleep + 30cm)

The existing damaged plaster is recommended to be suppressed to brick and it is advisable to deepen the fugues a few cm with a carpenter.

Old coatings that are not firmly adherent should be removed.

Work:

The mortar should be applied in at least two layers, a well -adherent splash and then in a coarser layer.Make the splashed layer from a more river mortar.

The thicker mortar should be applied when the splash layer has hardened.The thick layer consists of a gentle mortar, which is spooned with a spoon on the surface, distributed and smooth it with a wood smoothing (do not use a metal smoothie, as the pores are sealed).The thickness of the complete layer of two layers should be at least 2 cm everywhere.

If the thickness of the desired layer must be greater than 2 cm, another layer can be applied after the previous layer is tightened.Drying of the plaster depends on wall surface and weather.

Working temperature:

Depending on the weather, spraying (watering) is recommended every 2-3 hours for a few days after processing.Sudden dehydration can greatly worsen the quality of the product.Recommended application period between + 5 ° C and + 25 ° C.+20 ° C, humid, wet weather/ area The aftercare of the plaster is not required or partially necessary.

Other information:

The mortar should be well mixed after a longer period of time.

The surface should be made with a wood smoothing, the use of a metal or plastic smoothing blocks the poles.

Use a vapor permeability as paint.

Tool cleaning:

Before the mortar is hardened with water.

Safety Regulations:

In the case of work with our products, the most important physical, safety, toxicology and ecological data can be found on the safety data sheet for products.Provisions for hazardous substances must be observed.

Expiration date:

It can be stored in unopened original packaging for 36 months.

Manufacturer Warranty:

For proper mixing and use - 10 years!

Properties:

Hydraulic bonded indoor and outdoor use.

Highly hydrophobic water repellent

Status: Powder

pH value: 11.5 - 12.5PH

Size: 4μ

Color: white

Use temperature:-from 20C to + 370C

Working Safety Classification: XI (iritative)

Testament Department: A1

Packaging type: plastic bucket

Advantages:

Exoline® Aqua STOP - PAL surfaces are directly covered with cold cover.

Apply at a minimum thickness of 1-3 cm.(Publication 11m 2 / 1cm)

Can be worked easily and quickly

It enhances the efficiency of insulation through its water repellent properties.The opposite pressure in a wall plastered with exoline® additive is higher than the pressure on the capillaries (capillary depression)

Improves the durability, quality parameters of the plaster and improves masonry insulation!Insulating and wall drying!

It is a ventilation, thus preventing the growth of mold, fungi and other harmful substances!

Binding accelerator is also a fluid during drying!

Frost, acid, alkaline and oil standing!

Provides excellent abrasion resistance!

It is very resistant to strong temperature fluctuations!

(Illustrations in use)

If you have any questions about this product, please contact us: