Benefits offered by Exoline® product line:

Our products are primarily compatible with all commercially available cement -based construction products.

After mixing with Exoline® Aqua Stop D+ water, it can be easily worked, High adhesive, stable and excellent adhesive adhesive form a rahabar.Exoline® Aqua Stop D+ Water and weatherproof layer with high adhesive strength and elastic.

Using the product, you can change other systems, such as spreadable insulation, foils, heavy plates and other technological solutions.These technologies are obsolete expensive and significant requirements, and their preparation depends largely on human factors, which increases the risk, costs and time of construction.

Area of ​​use:

Ceramic and stone sheets

Stone sheets and mosaics (with paper or fiberglass carrier)

Porcelain mosaics

To cover.On-and-out and outdoor flooring, wall and ceiling

For heated floor structures

To place split stone slabs on the facade

Shape -shaped to natural stone

Mixing:

It is recommended with a low speed concrete mixer - a mixing drum at an angle of 35 ".

Preparation of wall surface:

The bad stone and brick pieces must be carved all the way to the hard part.

In the plinth part, clean the thickness of the wall above wetting.Eg: (Sleep + 30cm)

It is recommended that the existing damaged plasters be crushed to brick and it is recommended to extend the spots a few cm with a carpenter.

Old coatings that are not firmly adherent should be removed.

Work:

The mortar should be applied in at least two layers, a well -adherent splash and then in a coarser layer.Make the splashed layer from a more river mortar.

The thicker mortar should be applied when the splash layer has hardened.The thick layer consists of a gentle mortar, which is spooned with a spoon on the surface, distributed and smooth it with a wood smoothing (do not use a metal smoothie, as the pores are sealed).The thickness of the complete layer of two layers should be at least 2 cm everywhere.

If the thickness of the desired layer must be greater than 2 cm, another layer can be applied after the previous layer is tightened.Drying of the plaster depends on wall surface and weather.

Working temperature:

Depending on the weather, spraying (watering) is recommended every 2-3 hours for a few days after processing.Sudden dehydration can greatly worsen the quality of the product.Recommended application period between + 5 ° C and + 25 ° C.+20 ° C, humid, wet weather/ area The aftercare of the plaster is not required or partially necessary.

Other information:

The mortar should be well mixed after a longer period of time.

The surface should be made with a wood smoothing, the use of a metal or plastic smoothing blocks the poles.

Use a vapor permeability as paint.

Tool cleaning:

Before the mortar is hardened with water.

Safety Regulations:

In the case of work with our products, the most important physical, safety, toxicology and ecological data can be found on the safety data sheet for products.Provisions for hazardous substances must be observed.

Expiration date:

It can be stored in unopened original packaging for 36 months.

Manufacturer Warranty:

For proper mixing and use - 10 years!

Properties:

Hydraulic bonded indoor and outdoor use.

Highly hydrophobic water repellent

Status: Powder

pH value: 11.5 - 12.5PH

Size: 4μ

Color: white

Use temperature:-from 20C to + 370C

Working Safety Classification: XI (iritative)

Testament Department: A1

Packaging type: plastic bucket

Advantages:

Exoline® Aqua STOP - PAL surfaces are directly covered with cold cover.

Apply at a minimum thickness of 1-3 cm.(Publication 11m ² / 1cm)

Can be worked easily and quickly

It enhances the efficiency of insulation through its water repellent properties.The opposite pressure in a wall plastered with exoline® additive is higher than the pressure on the capillaries (capillary depression)

Improves the durability, quality parameters of the plaster and improves masonry insulation!Insulating and wall drying!

It is a ventilation, thus preventing the growth of mold, fungi and other harmful substances!

Binding accelerator is also a fluid during drying!

Frost, acid, alkaline and oil standing!

Provides excellent abrasion resistance!

It is very resistant to strong temperature fluctuations!

NOT AVAILABLE AT THE MOMENT!